DIY Halloween Witch Wands with Mini Spell Scrolls

Did you ever notice there are fairy wands everywhere for dress up and Halloween, all sparkly and covered in stars, but I have never seen a magic wand made just for witches? With my ongoing witchy theme for Halloween, I decided to fix that.

I grabbed a handful of old spindles from my stash and turned them into witchy magic wands with fun little spell scrolls tucked inside. They are easy to make, inexpensive, and you can use them for costumes, party favors, or Halloween decor.

I started them using bright traditional Halloween colors, but those colors aren’t my style. I did leave two of them that way, which I will give to the neighbor girls on the corner to play with, but then I switched gears and made three more in black and white.

So in this post, I am sharing both styles. You can make the wands in the bright traditional colors for costumes and kids, or try the black and white version if you want something softer. The steps are the same; it just comes down to the paint and embellishments you choose.

How to Make a DIY Witch Wand for Halloween

Supplies

Step 1 – Prepare Spindles

Give the spindles a good wash with Dawn soap and water. Let dry.

Trim the tips off the spindles, or cracked ends, with a mitre saw or hand saw. Then sand with 120 grit to make sure there are no slivers.

Step 2 – Paint the Spindles

For the traditional version, paint your spindles in bold Halloween shades like black, purple, orange, or green. I painted mine in stripes using a small artist’s brush from the dollar store, holding the brush firmly in one hand while twisting the spindle in the other to form straight lines around the curves. It took two coats. Let dry according to your paint’s directions.

For the neutral version, I repainted the spindles with two coats of white paint to cover the dark purple and black. For your spindles, you could paint them solid white like mine, or add a bit of light distressing if you prefer a more vintage look.

Spray varathane over the spindles. Let dry.

Step 3 – Create Base for Embellishments

Next, cut a small hole in the bottom of the ball, being careful not to poke all the way through. Fill the hole with a combination of E6000 and hot glue, then insert the wood spindle. Hold it in place until secure, and let it dry until hard.

Attach a Styrofoam ball to the end of your spindle to give you more room for decorations. For the traditional version, paint the ball black before attaching it. I then wrapped it with Dollar Tree mesh, securing it firmly with a small pull tie. I used two pieces of mesh about 10 inches long, which left a bit of a frill at the bottom.

For the neutral version, I painted the balls first and then wrapped them in fabric, but you could skip the paint and just cover them if you prefer.

To cover the neutral witch wands, I used some black fabric scraps (dollar store garden weed fabric). I made an 11-inch circle pattern by tracing around a lid, then cut a fabric circle for each wand.

Step 4 – Add Black Feathers

The traditional colored DIY witch wands have bundles of black feathers to cascade down and decorate the wand. I left the feather off the neutral wands, but they would be beautiful on those as well if you want to add them.

Take four feathers, line them up, and wrap them tightly with a foot-long piece of florist wire. Twist the wire to secure the feathers in place, then add a bit of hot glue and let it harden.

Once the feather bundle is set, use the remaining wire to wrap it around the base of the wand. Twist firmly and secure with more hot glue.

Step 5 – Add Raffia Nests

The black crow needed something to bridge the space between the ball and the bird. I tried a few ideas, like using a doily or lace, but the best option was to add raffia and create a little nest. It is simple to attach: just add plenty of glue under the raffia, press it on top, and trim if needed.

Hint: You can also use florist pins to help secure the raffia if your wands are just for display. I left them out because hot glue works well on its own, and skipping the pins makes the project safer for kids.

Step 6 – Add Ribbon Cascades

For the traditional wands, cut long strands of ribbon, add a pick of sparkling beads, and tie them around the top of the spindle to cover the pull tie. Let the ribbons hang long and flowing to give a magical look. A mix of velvet, sheer, satin, and various colors adds beautiful interest.

For the neutral wands, instead of using feathers, I went with a more elaborate, feminine look to make them feel pretty rather than spooky.

I began by cutting two feet of six-inch-wide black mesh. I gathered it in folds to make it narrower and tied it around the pull tie at the top of the spindle, pulling it tight and sealing it with a dab of hot glue. I then finished tying the bow so the loops were the same size and left the ends trailing down for now.

Next, I took a length of leftover vintage lace, cut it into three equal pieces, and threaded each length through the center of the mesh bow. Once threaded, I tied it into a knot. I had some striking striped black and soft white ribbon, so I cut two lengths about two feet each and tied a long, loopy bow, leaving long tails hanging down. I attached that ribbon with hot glue.

Step 7 – Perch the Crow

Hot glue a mini black crow to the very top of each wand. Then cut two pieces of heavier gauge wire and bend each one into a U-shape. Place a wire over each foot and push them into the Styrofoam ball for extra stability. If the wands are for children, I recommend still doing this step, but also adding lots of hot glue under the raffia so the pins are extra secure and will not come loose.

Step 8 -Make the Mini Scrolls

Print out the free paper scroll printables onto craft paper and cut them into small rectangles. Roll them up tightly and tie with thread or twine. Stick them at an angle near the bird’s legs so it looks like the crow is carrying a witch’s message.

Step 9 – Final Touches

Each little crow was tied with black ribbon to match the scrolls, and I tucked a small plastic flower under the crow for a pretty touch.

To display the home decor neutral Halloween witch wands, I placed them in a clear vase, with fairy lights, and glittering black branches.

If you like this Halloween project, don’t forget to save it to Pinterest so you can find it again when you are ready to make your own witch wands. These DIY witch wands are a fun way to mix spooky and whimsical, and they’re easy to customize in bold or neutral colors.

More DIY Witch Crafts for Halloween:

If you’re into a witchy theme for Halloween, here are a few of my other witch-themed tutorials.

Dollar Tree Plunger Witch Broom for Indoors or Out

DIY Elegant and Spooky Chandelier

DIY Witch Frog Art in a Thrifted Frame